| SIMATIC PN/PN Coupler for deterministic data exchange between max.4 PN-Controller per subnet, also from subnet to subnet, PROFIsafe data exchange, I/O-, MSI-, MSO- and data record communication, redundant power supply, PN-connection via SIMATIC BusAdapter (BA), delivery w/o BusAdapter |
| General information |
| Firmware version | V4.2 |
| FW update possible | Yes |
| Product function |
| I&M data | Yes; I&M0 to I&M3 |
| Tool changer | Yes; Docking station and docking unit |
| Local coupling, IO data | Yes |
| — Number of coupling modules | 16 |
| — Number of coupling submodules per module | 4; 1x write, 3x read |
| Local coupling, data records | Yes |
| — Number of coupling modules | 16 |
| — Number of coupling submodules per module | 4; 1x write, 3x read |
| — Record length, max. | 4 096 byte |
| — FIFO depth in storage mode | 8 |
| Engineering with |
| STEP 7 TIA Portal configurable/integrated as of version | STEP 7 V15.1 or higher |
| PROFINET as of GSD version/GSD revision | V2.3 |
| Installation type/mounting |
| Mounting | Mounting rail 7.5 mm and 15 mm |
| Supply voltage |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 19.2 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Mains buffering |
| Mains/voltage failure stored energy time | 10 ms |
| Input current |
| Current consumption, max. | 360 mA; For 19.2 V input voltage at the right-hand supply terminal, including 2 plugged BA 2x LC |
| Inrush current, max. | 1.6 A |
| I²t | 0.031 A²·s |
| from supply voltage 1L+, max. | 320 mA; For 19.2 V input voltage at the left-hand supply terminal, including 2 plugged BA 2x LC |
| Power loss |
| Power loss, typ. | 4 W; For 24 V input voltage and 2 plugged BA 2x RJ45 If BusAdapters with an optical interface are plugged, there is an additional 750 mW per optical interface (3 W with 2 plugged BA 2x LC) |
| Address area |
| Address space per module |
| Address space per module, max. | 254 byte; max. 254 bytes of input data and 253 bytes of output data |
| Address space per station |
| Address space per station, max. | 1 440 byte; per input / output |
| Hardware configuration |
| Submodules |
| Number of submodules per station, max. | 116 |
| Interfaces |
| Number of PROFINET interfaces | 2; One PROFINET interface per line side |
| With optical interface | Yes; Via SIMATIC BusAdapter |
| Supports protocol for PROFINET IO |
| automatic detection of transmission rate | Yes |
| Transmission rate, max. | 100 Mbit/s |
| 1. Interface |
| Interface types |
| Number of ports | 2; via BusAdapter |
| integrated switch | Yes |
| BusAdapter (PROFINET) | Yes; Compatible BusAdapter: BA 2x RJ45, BA 2x FC, BA 2x SCRJ, BA SCRJ / RJ45, BA SCRJ / FC, BA 2x LC, BA LC / RJ45, BA LC / FC |
| Protocols |
| PROFINET IO Device | Yes |
| Open IE communication | Yes |
| Media redundancy | Yes; As MRP or MRPD client; max. 50 or 30 devices in the ring |
| 2. Interface |
| Interface types |
| Number of ports | 2; via BusAdapter |
| integrated switch | Yes |
| Protocols |
| PROFINET IO Device | Yes |
| Open IE communication | Yes |
| Media redundancy | Yes; As MRP or MRPD client; max. 50 or 30 devices in the ring |
| Interface types |
| RJ 45 (Ethernet) |
| Transmission procedure | PROFINET with 100 Mbit/s full duplex (100BASE-TX) |
| 10 Mbps | No |
| 100 Mbps | Yes; PROFINET with 100 Mbit/s full duplex (100BASE-TX) |
| Autonegotiation | Yes |
| Autocrossing | Yes |
| Protocols |
| Supports protocol for PROFINET IO | Yes |
| Protocols (Ethernet) |
| TCP/IP | Yes |
| SNMP | Yes |
| LLDP | Yes |
| ping | Yes |
| ARP | Yes |
| PROFINET IO Device |
| Services |
| — Isochronous mode | No |
| — Open IE communication | Yes |
| — IRT | Yes |
| — PROFIenergy | No |
| — Prioritized startup | Yes |
| — Shared device | Yes |
| — Number of IO Controllers with shared device, max. | 4; per line side |
| Redundancy mode |
| MRP | Yes |
| MRPD | Yes |
| PROFINET system redundancy (S2) | Yes; NAP S2 acc. to IEC |
| Open IE communication |
| TCP/IP | Yes |
| SNMP | Yes |
| LLDP | Yes |
| Isochronous mode |
| Isochronous operation (application synchronized up to terminal) | No; For operation on isochronous bus |
| Interrupts/diagnostics/status information |
| Status indicator | Yes |
| Alarms | Yes |
| Diagnostics function | Yes; Parameterizable |
| Diagnostics indication LED |
| RUN LED | Yes; Green LED |
| ERROR LED | Yes; Red LED |
| MAINT LED | Yes; yellow LED |
| Monitoring of the supply voltage (PWR-LED) | Yes; green PWR LED |
| Connection to network LINK (green) | Yes; 2x green link LEDs on BusAdapter |
| Potential separation |
| between supply voltage and electronics | Yes; to power input 2 |
| between Ethernet and electronics | Yes |
| Isolation |
| Isolation tested with | 707 V DC (type test) |
| Standards, approvals, certificates |
| Network loading class | 3 |
| Security level | According to Security Level 1 Test Cases V1.1.4 |
| Ambient conditions |
| Ambient temperature during operation |
| min. | 0 °C |
| max. | 60 °C; = Tmax for horizontal installation; for vertical installation Tmax = 50 °C |
| Altitude during operation relating to sea level |
| Installation altitude above sea level, max. | 2 000 m |
| Ambient air temperature-barometric pressure-altitude | On request: Ambient temperatures lower than 0 °C (without condensation) and/or installation altitudes greater than 2 000 m |
| Mechanics/material |
| Strain relief | Yes; Optional, for RJ45 and FC BusAdapter only |
| Dimensions |
| Width | 100 mm; Minimized with good handling |
| Height | 117 mm |
| Depth | 74 mm; with mounting rail |
| Weights |
| Weight, approx. | 200 g; without BusAdapter |
| last modified: | 03/12/2019 |
